2013 F-150 EcoBoost Oil Quarts: Exact Amount Inside
A 2013 Ford F-150 EcoBoost takes 6.0 quarts of engine oil with the oil filter changed, and Ford specifies 5W-30 for the 3.5L EcoBoost.
Oil Capacity
The most important number for a 2013 EcoBoost owner is the fill amount after a standard oil change, because that is the figure you use when buying oil and checking the dipstick. Ford's owner-content listing for the 3.5L EcoBoost shows engine oil capacity at 5.7 L, which converts to 6.0 quarts with the filter installed.
| Engine | Oil type | Capacity with filter | Notes |
|---|---|---|---|
| 3.5L EcoBoost V6 | 5W-30 | 6.0 quarts | Ford lists 5.7 L, approximate dry fill capacity. |
That 6-quart figure is the one most owners and service guides use for the 2013 F-150 EcoBoost, and it is consistent across multiple independent references that summarize Ford's specifications.
What To Buy
- Buy 6 quarts of SAE 5W-30 oil for a routine change on the 3.5L EcoBoost.
- Use a quality oil filter designed for the 3.5L EcoBoost application.
- Check the dipstick after refilling, because the final amount can vary slightly depending on drain time and filter fill.
If you are planning the service yourself, the cleanest approach is to add about 5.5 quarts first, then top off slowly while checking the dipstick until the level sits in the safe range. That helps avoid overfilling, which is more annoying than slightly underfilling because it can push the oil level above the mark and cause foaming or leaks.
Why The Number Matters
The 3.5L EcoBoost is a turbocharged engine, so oil choice and oil level matter more than they do on a basic naturally aspirated setup. Ford's spec for 5W-30 is intended to support lubrication under load, especially when the truck is towing, idling in traffic, or running hot in summer conditions.
In practical terms, the difference between the correct 6-quart fill and a guessed fill can be enough to trigger a low-oil reading or a messy overfill. A lot of repair write-ups from the early 2020s repeat the same basic rule: start with 6 quarts on the 2013 3.5L EcoBoost, then verify on the dipstick after the engine has had a moment to settle.
Service Steps
- Drain the old oil completely and replace the filter.
- Add about 5.5 quarts of SAE 5W-30 first.
- Start the engine briefly, then shut it off and wait a few minutes.
- Check the dipstick and top off until the level is correct.
- Confirm there are no leaks at the drain plug or filter.
That simple sequence is the easiest way to land on the correct oil change volume without guessing. It also helps explain why some owners report using slightly less than 6 full quarts in the real world, since residual oil, filter fill, and drain time can all affect the final amount.
Capacity Context
Ford offered multiple engines in the 2013 F-150 lineup, and the oil capacity depends on which engine is under the hood. The 3.5L EcoBoost sits in the middle of the range, with a smaller capacity than the 5.0L V8 but the same 6-quart neighborhood as the other V6 options.
| 2013 F-150 engine | Oil type | Capacity |
|---|---|---|
| 3.5L EcoBoost | 5W-30 | 6.0 quarts |
| 3.7L V6 | 5W-20 | 6.0 quarts |
| 5.0L V8 | 5W-20 | 7.7 quarts |
| 6.2L V8 | 5W-20 | 7.0 quarts |
That table shows why the 2013 truck owner should always verify the engine code before buying oil, because a wrong assumption can leave you short by more than a quart. Ford's published capacity data and third-party maintenance guides agree that the 3.5L EcoBoost is the 6-quart, 5W-30 application.
Real-World Notes
Independent service content from 2011-2026 F-150 oil kits also places the 3.5L EcoBoost at 6.0 quarts, which lines up with Ford's published capacity information. That consistency is useful because it reduces the chance of confusion when shopping for oil at a parts store or ordering a maintenance kit online.
"Engine oil (with oil filter), 5.7 L (6.0 qt)."
That Ford capacity line is the clearest single reference point for a 2013 EcoBoost oil change, and it is the one most mechanics will work from in practice.
FAQ
Final Answer
The exact answer for a 2013 F-150 EcoBoost is 6.0 quarts of SAE 5W-30 with a filter change. That is the number to use for buying oil, planning the service, and checking your final fill level.
What are the most common questions about 2013 F 150 Ecoboost Oil Quarts Exact Amount Inside?
How many quarts does a 2013 F-150 EcoBoost take?
It takes 6.0 quarts of oil with the filter changed. Ford lists the 3.5L EcoBoost at 5.7 L, which equals 6.0 quarts.
What oil should I use?
Use SAE 5W-30 for the 2013 3.5L EcoBoost. That is the viscosity repeatedly associated with Ford's published guidance for this engine.
Do I need exactly 6 quarts?
Six quarts is the target fill amount, but the dipstick should be the final check. Small variations can happen because of drain time, filter fill, and how completely the old oil was removed.
Is the EcoBoost different from other 2013 F-150 engines?
Yes. The 3.5L EcoBoost uses 5W-30 and 6.0 quarts, while the 5.0L and 6.2L engines use different oil types and capacities.
Can I overfill it?
Yes, and that is something to avoid. Add oil gradually and verify the level on the dipstick so the engine stays in the correct range.